The National 2½" Gauge Association

Keeping the spirit of the past alive for tomorrow and looking to the future
The National 2½" Gauge Association is a not-for-profit organisation



Lynton and Barnstaple 2-6-2 Tank Locomotive 'LYD'

Construction Notes

(note that clicking on an image will take you to a larger version)

 

07/11/2025

A start at last although a small one. All the fixing angles for the front and rear beams have been made and the frames temporarily bolted together just to see what they look like.

 

The frame plates and the front and rear beams were laser cut by Ed at MEL and came out very well. The majority of the holes have been cut which will save a lot of work but anything less than 2.2mm will need to be marked out and drilled as apparently holes smaller in diameter than 75% of the material thickness are difficult to cut cleanly.

The 8mm x 8mm brass angles were milled from 3/8" x 3/8" x 1/16" but at a pinch you could use 5/16" x 5/16" which will only be about 0.1mm undersize.

None of the brass angle I have ever purchased has been at 90° on the outside faces (it's usually a few degrees less) so it will need to be milled square otherwise the frames will pull out of square when the angles are fitted. I did this by clamping the angle in the milling vice and taking a light skim off one of the faces.

 

 

I only had to take off about 0.1mm to clean up the face. Note that the angle is clamped against the back jaw of the vice using a length of 1/8" dia. rod. This is to ensure it sits against the jaw properly. The leg of the angle is usually slightly tapered so if you just clamp it using the front jaw, it may not sit flat against the rear jaw.

Next the angle was milled to the correct size i.e. 8mm x 8mm.

 

 

Finally, the angle is milled to length.

 

 

I milled one end square on all the angles, then used a thin parallel as a vice stop (must get a proper one!) to mill the other end to length. Using a stop enables all the angles to be quickly milled to the same length.

I drilled all the fixing holes in the angles using my DRO on the mill which made it quick and easy to do but you can do it the conventional way by clamping the angles in place on the frames and the beams and then spotting the holes through.

 

The angles are permanently rivetted to the frames with 3/32"/2.5mm soft iron rivets but on the full size loco the beams are fastened to the angles with 'fitted' roundhead bolts with nuts on the inside. You could save some work by just using ordinary 7BA hex head bolts if you are not too bothered about them looking prototypical. I haven't checked yet but it may be possible to machine down the heads of standard size hex head 7BA bolts which would save making the special bolts entirely from scratch.

09/11/2025

There is a bracket (Drawbar Support Channel) that fits behind the front and rear beams and connects to the side frames. I have had these 3D printed in stainless steel as an experiment and also had a set of parts laser cut so they can be fabricated.

 

 

The 3D printed brackets came out quite well but had a distinct curve in the front face. I think this was probably caused by uneven shrinkage when the parts were printed. I wasn't sure if these parts would be useable but decided to have a go at straightening them if possible.

I tried using the milling machine as a press but I was afraid of using too much pressure for fear of damaging the mill so ended up using the bench vice. The brackets are wider than the vice jaws so I put a piece of steel flat bar inbetween the jaw and the part. Now, I was fully expecting the thin webs of the bracket to crack as soon as I applied pressure so I was surprised when they didn't. It took a lot of pressure to straighten the bracket as it kept springing back to it's original shape but it did straighten out.

 

 

I have no doubts now that 3D printed metal parts are plenty strong enough for what we will use them for.

Although the front face of the bracket was probably now flat enough to use, I decided to machine it and the end faces to make sure they were all square to each other. If not, bolting them up may distort the frames.

Firstly, the bracket was put in the machine vice with the front face against the bottom of the vice and a skim taken of the ends of the side faces to ensure they would be the same distance from the front face. They were slightly different heights.

 

 

Next, the bracket was inverted and a skim taken off the front face until it was nice and flat. The brackets are wider than my machine vice so I put a parallel in first and sat the bracket on that.

 

 

Finally, the bracket was inverted again and the ends milled with the side of the cutter. I did this using the full length of the cutter (a 12mm Carbide endmill) but it didn't really like cutting at full depth. This 3D printed 316L stainless is pretty tough stuff but can be machined with care.The brackets ended up being about 0.7mm too long when printed so about 0.35mm had to be removed from each end to get them to size.

 

 

I did have the mounting holes printed in the brackets but some of them were slightly in the wrong place so I probably would not do that again and drill them afterwards. I did try redrilling them using the DRO in the mill as they were undersize anyway but, of course, the drill just follows the original hole. It really needed using an endmill of the correct size. As it happens, all the bolts on the front face fitted easily when the bracket was offered up into place so the holes can't have been too far out. The holes in the end faces were slightly out of line with the holes in the frames so were just drilled out using the frames as a guide.

 

.

 

On final assembly, the brackets are bolted in place with 7BA hex head bolts (except for the centre four holes that also hold the coupler pocket which are 8BA) On the full size loco these bolts have a small centre mark in the middle of the heads.

13/11/2025

The rear drawbar support channel has now been machined in a similar fashion to the front one. This time the 3D print did not take as much straightening and the front face came out very flat so I just rubbed that with a file rather than machine it. The end faces were machined though as this bracket was also about 0.7mm too wide. Strangely enough, the holes in the front faces were spot on in position this time and just needed drilling out. The holes in the end faces were slightly out again so were drilled out from the frames as before. I am beginning to think that the dimensions of these 3D printed parts can be a bit unpredictable and vary from part to part.

I decided to go back now and drill the missing small holes in the frames and the beams, starting with the beams. These need some 1.6mm holes (check size from the rivets that you will be using) drilling along the top edge for fastening the pieces of 6mm x 6mm angle that will support the running boards. Once again, these were drilled using the DRO in the mill. The rivets are flush on the outside of the beams so these holes need a small countersink for the rivets to be rivetted into.

 

 

I used a 5mm 90° spot drill to countersink the holes as I didn't have a normal countersink bit small enough.

 

:

 

The front beam also requires three 2.5mm coutersunk holes for mounting the lubricator.

 

 

Front and rear beams with all the holes now drilled:

 

 

Note that there are some holes that will not be used in the final model. These were used on LEW for extra brackets for supporting the cow catcher but these brackets are not fitted to LYD although the beams are drilled for the mounting bolts

 

Photo courtesy of Brian Kerens

 

I have just purchased a cheap TIG welder as I thought it would be very useful to be able tack the laser cut parts together for the various fabrications before finally silver soldering them. I have never done any TIG welding before so that should be fun! I think tacking them together first will be a lot easier than having to make some sort of jig to hold everything in place for soldering. We shall see.

14/11/2025

I had a thought today that I hadn't drilled the 3mm holes for mounting the vacuum pipes onto the beams so I went ahead and drilled those. It wasn't until I looked at the beams afterwards that I realised that I had already had the holes laser cut. I hadn't noticed this when drilling and countersinking the small holes and Sods Law decread that I had got the beams back to front i.e. the laser cut holes on the wrong side so they didn't coincide with the holes that I had just drilled. If they had then I would have noticed my mistake. Consequently, I now have two extra 3mm holes that will need to be filled in! So the moral is that if you use the laser cut beams then make sure that you get them the correct way round before drilling the small holes. Looking at the beams, the front beam has the 3mm hole on the left and the rear beam has the 3mm hole on the right.

I received some 7BA large Hex head bolts today so I measured the heads and they are large enough to be turned down to make the round head bolts needed for fastening the front and rear beams. You could probably just get away with the small hex bolts if you were careful to get them to run truly when turning off the hexes but they may come out undersize. In actual fact I don't have any drawings for these bolts so had to ''guestimate' the diameter of the heads from photographs so the 4mm dia. that I have shown may not be correct anyway.

I made a start on drilling the small holes in the frame plates. Note that there are differences between the lefthand and righthand sides so be sure to check which one you are drilling and countersinking. The majority of the holes are for 1.6mm rivets and these need to be countersunk on the inside of the frames. There are also some of the larger holes that require countersinking on the outside so, again, make sure you have the frames the right way round.

I took the dimensions for the holes from the centreline of the horn slots (found using an edgefinder) and did them in three setups to avoid having to move the mill table long distances.

Drilling the holes rfor the rivets:

 

 

Drilling the holes for attachment of the oil boxes:

 

 

Note that I have marked the frames with a Sharpie so I don't get them mixed up! Be careful with the holes behind the trailing horn slot as some of them are drilled 2.05mm (no.46) for tapping 7BA. I will drill all the holes first and then go back and do the countersinking afterwards.

15/11/2025

All the holes are now drilled in both frame plates and the relevant holes countersunk.

 

 

The laser cut parts had been kept in the house for several months before starting work on them and when I got them out the frames plates had gone quite rusty. One or two of the other parts had started to rust as well but most were fine. I know my house probably is a bit damp at times which could have caused the problem but it seems strange that only the frame plates were badly affected. I did clean them with a fine wire brush and red scotchbrite to remove most of it but I noticed today that it had started to come back. The workshop is pretty dry as I have a dehumidifier running 24/7 and I have been using cutting oil for drilling the holes so the plates should be quite oily but it's as if there is something on the surface of the steel causing it to rust. Anyway, I have attacked them with the scotchbrite again.

16/11/2025

Today I made the Front Frame Stiffening Angles. These are just lengths of 8mm x 8mm x 1.6mm angle which were squared up and machined to size as for the previous angles. These are handed so don't make two the same!

 

 

These are rivetted to the frames with 1.6mm (1/16") rivets. I am not sure what the recess in the outside edges is for but presumably to give clearance for something, maybe the oil pot on the front coupling rod when it is at it's highest point? The full size loco has it so I have included it.

I have had the Rear Frame Stffening Angles laser cut but they can be machined from suitable brass angle if desired. That would avoid the silver soldering job for the fabricated version. Once again, these are handed.

 

20/11/2025

Today I decided to have a go at the Rear Frame Stiffening angles. I now have all the gear to go with the new TIG welder so no excuse not too. I did realise when I unpacked the disposable gas cylinder I had purchased that I had bought the wrong gas! It should have been pure Argon but I had accidentaly bought Argon/CO2 mix which is for MIG not TIG. I do have an Argon bottle for my MIG welder but it's empty and filling it means a trip to BOC. Anyway, I decided to give it a try with the mixed gas and it did work although the welds were far from perfect. To be fair, this is the first time I have used TIG and so I haven't much clue as to what I am doing! I only wanted to tack the two parts of the angle together anyway so it didn't need to be perfect so long as it held together.

I cut the two parts of the angle part and filed off the stubs left from the joining tags. When I tried to fit them together they would not quite go together but a slight rub with a file on the ends of the slots and they fitted together perfectly. The tabs were a good tight fit in the slots and they had to be tapped together with a small hammer. They were such a good fit that perhaps I didn't need to weld them but I decided to anyway. I didn't want the parts coming apart or moving whilst I silver soldered them.

 

 

I then put a small tack weld on each tab to hold the two parts together.

 

 

Not too bad if you don't look closely! I did practice a bit on some scrap 1.6mm steel before hand and ended up using the 20amp setting so that the metal didn't get too hot. They did come out a bit bowed so will have to be straightened out before rivetting to the frames.

I then made a bit of a mess silver soldering them together. I grossly over estimated the amount of solder needed and ended up with a huge fillet in the corner. What I did was cut short lengths of 1.5mm Silverflo55 and laid them in the corner of the joint and I just used far too much (I must admit that I don't normally do this. I prefer to feed the solder in by hand). I then had to reheat the parts and run off the excess solder. That meant that the solder flowed where I didn't really want it and filled up some of the rivet holes. It all cleaned up reasonably well in the end though. I will know better next time.

 

 

I normally use sulphuric acid or citric acid as a pickle but this time I tried using brick cleaner (Hydrochloric acid) and it does seem to work a lot better for steel. The problem with using sulphuric acid for steel is that if the acid has been used for copper, anything steel gets instantly copper plated!

As mentioned, some of the holes had become blocked with excess silver solder so I drilled those out using the frame plates as a jig. I just clamped the angles to the frame plate using a couple of rivets through two of the unblocked holes to line them up correctly.

I have also rivetted on the Front Stiffening angles using 1.6mm soft iron rivets.

 

 

A few weeks ago I bought an aircraft type rivet squeezer for doing all the rivetting rather than rivet by hand but I need to make some dies for it as the ones that came with it are far too big. I will leave rivetting the rear angles on until I have got that sorted.

29/11/2025

I haven't had time to do much over the last few days but tonight managed to tack one of the fabricated Drawbar Support Channels together. This was quite straightforward, the only fiddly bit is that the edges of the vertical pieces need to be chamfered where they fit together. I just did this with a file and made the angle approximately 67° using an angle gauge. To begin with, the top and bottom pieces were fitted and tacked to the front plate. Whilst tacking them together I clamped them to a length of square steel bar to keep them at 90° to each other. Then the end plates were fitted but before finally fitting them for good check the width of the bracket and adjust if necessary. I must have got lucky as mine was almost exactly 118mm! Finally the angled corner plates were fitted. These needed a bit of fettling to get the joints to fit together flush which I was expecting.

 

 

I'm not going to bother silver soldering this bracket together as I'm not going to be using them. I just wanted to check that the laser cut fret was correct and fitted together. After soldering check the bracket for squareness. The steel should be fairly soft so easy to bend slightly if necessary. These brackets will need the mounting holes spotting through from the frames and drilling as I have not included any holes other than the large centre hole for the coupling (I may alter the drawing for the fret to include the holes on the front plate).

03/12/2025

The Front and Rear Saddle Stretchers are each a two piece fabrication consisting of a 2mm plate and a 6mm 'Rib' Section. The Rear Stretcher is modified from the full size loco to provide mounting for the two axle pumps.

 

 

The rib frets may need some 'blobs' filiing off where the laser has melted the metal and formed a drip. My rib for the Rear Saddle Stretcher was also a bit bowed and needed flattening. To hold the rib to the plate I clamped the plate to a piece of flat steel and then clamped the rib on top. I bought a load of cheap mole grip type clamps to help with this. I paid about £20 for eight from Amazon but there is a chap who sells them cheaper at the Midlands Exhibition.

 

You will need to take some time making sure that the edges are all correctly aligned and you may need to adjust the shape of the rib so that it matches the plate as closely as possible. Also make sure that you put the rib on the correct side of the plate. The slot at the bottom of the plate needs to be on the lefthand side when the rib is on the top. I will be tacking the parts together before final silver soldering, perhaps tomorrow if I get chance.

05/12/2025

I tacked both of the Saddle Strechers together yesterday. My original intention was to put tack welds into the inside corners between the plate and the rib but I just could not get it to work properly. Whether It was due to my lack of experience (probably) and possibly because of the difference in thickness of the two pieces. Also the steel flat I had the parts clamped to made a big heatsink and drew the heat out of the weld. In the end I gave up on that idea and just tacked them together on the outside. This was much easier to do although it did make holding the parts in alignment more difficult. I could have done the tacking with the parts still clamped to the piece of steel flat but with my luck I would have probably welded the parts to the steel flat as well! Instead, I clamped the parts together held in the vice.

Today I silver soldered both the stretchers and that went very well this time. I fed the solder in by hand rather than use pieces laid in the joint and that worked much better.

 

 

They still need some final cleaning up before fitting them to the frames and drilling the mounting holes.

Next I had a go at the Rear Bridal Stretcher. This is a very simple fabrication with two flanges and the actual stretcher.

 

 

This was tacked together after clamping the parts to a piece of square steel bar to keep them aligned and square.

 

 

Ready for silver soldering:

 

 

I did notice after tacking that I hadn't got the flanges tight against the stretcher so these may come out slightly too wide. If so, I will just trim them to width in the mill.

Incidently, I realised yesterday that I had got the gas preflow setting on the TIG welder set to zero so the gas was not flowing until after the welding arc struck. That's probably why some of the welds looked sooty. The gas needs to flow before the arc strikes so that the weld is shielded before the arc strikes. After setting the preflow to 1 second the welds turned out a lot cleaner.

I then made a start on the Front and Rear Frame Stays. These are more complicated as they have lugs for mounting the Brake Hangers. I thought that I had taken a photo of the frets before I started to assemble them but I hadn't so I have used some photos I took of the laser cut parts after they had arrived. The frets also have the parts for the Firebox Stay.

 

 

The parts were separated and then the top tacked to the stretcher plate. Again, the parts were clamped to the square bar to keep them aligned and square.

 

09/12/2025

Today I finished tacking the Front and Rear Frame Stays together ready for silver soldering.

 

 

When I fitted the end flanges I noticed that I have made a mistake on the drawing for the laser cut fret which leaves a gap of 0.5mm at the top where the flanges are notched to take the top piece.

 

 

I think I originally made the top 2mm thick but that did not leave much clearance for the top fixing bolts so I reduced it to 1.5mm but didn't change the fret drawing. I'll modify that and send it to Ed at MEL. If I knew what I was doing I could fill the gap with weld but I'm not going to risk it with my welding! I'll fill the gap with a bit of shimstock before silver soldering instead.

12/12/2025

The fret for the firebox Stay has the front, sloping part and the top flange all in one piece.

 

 

 

The idea was to bend it to shape but as it's 2mm thick I think that would be difficult to do. I did think of cutting a vee where the bends would need to be but I didn't have a tool that was really suitable for the job. I did try a 90° spotting drill but that didn't cut very well. In the end I just cut it up into the three pieces needed but I don't think that the thin piece that forms the top flange is really needed so I didn't fit that. I left the sloping piece over length and that will be trimmed off after silver soldering. It should be possible to trim the edge to form the top flange or at least look like the top flange. As on the Drawbar Support Channel the edges of the front and sloping part need to be filed to an angle so that they fit together neatly. I managed to tack it all together with some creative clamping to hold the sloping piece in place.

 

 

Note that I've now altered the drawing for the frets for the stretcher to make the front, sloping part and the top flange, if needed, as separate pieces.

 

I've now silver soldered the rear Bridle Stretcher together along with the Front and Rear Frame Stays and the Firebox Stay. Not my neatest soldering but I find silver soldering steel a bit of a challenge. Give me copper or brass anyday!

 

 

They will be ok after cleaning up. They will all be painted anyway which will help cover up any untidy bits! They may need a bit of filler in places to fill in any gaps. In the photo I have already cleaned up the Rear Bridle Stretcher and drilled the mounting holes using the DRO in the mill.

 

 

To be continued

 

 

 

 

 

This page was last updated on 12/12/2025